Pas de fournisseur
Marque: Eric Grauffel
Rouleau de 2000 patches. Diamètre 23mm Couleur Dispo: Blanc, Noir ou Marron
Référence: SP500
AFIN DE VALIDER VOTRE COMMANDE, VEUILLEZ NOUS FAIRE PARVENIR LES DOCUMENTS SUIVANTS À L'ADRESSE ADMIN@ERICGRAUFFEL.COM : Copie de votre licence FFT ou Permis de chasser (En cours de validité) Copie recto verso de votre pièce d’identité (CNI, passeport, en cours de validité)
Marque: Sellier & Bellot
MUNITIONS CAT. B Afin de valider votre commande, veuillez nous faire parvenir les documents suivants à l'adresse admin@ericgrauffel.com : Numéro SIA Copie recto verso de votre pièce d’identité (CNI, passeport, en cours de validité) Copie de votre licence FFTir (Détention de 1000 Munitions maximum /par arme , dans la limite d'achat de 3000 Munitions...
Bannière
Produit testé & utilisé par notre équipe
Expédié sous 24H
Téléchargez vos documents pour les produits classés
What an adjustable gas block is to an AR, the lock piece is to the roller-delayed JP-5™ platform. This easily interchangeable component allows you to tune the recoil impulse of your rifle to suit whatever ammo or configuration you want to run.
Like every part we make, our JP-5™ Lock Pieces are a premium component manufactured from a proprietary steel and finished with a highly lubricious nitride coating for low wear and low friction.
Selecting a Lock Piece For Your JP-5™
Lock pieces for the JP-5™/MP5 pattern operating system are distinguished by the angle of the roller bearing surfaces. Most JP-5™ models will ship with the 80° lock piece. This angle determines how much force is required to open the action. The larger the angle, the easier it is for the action to open. So, systems with higher pressure will take a lower angle of lock piece and vice versa.
If you increase the pressure in your system—e.g., changing to a longer barrel, adding a suppressor, switching to higher pressure ammo—a lower-angled lock piece will function better. If you are decreasing the pressure, a higher-angle lock piece might function better.
In general, if your JP-5™ cycles weakly and unreliably, a higher angle of lock piece is recommended. If the bolt is cycling violently with the SCS bottoming out noticeably in the buffer tube, a lower angle of lock piece will help. Be aware that under-delaying the JP-5™ combined with high-pressure ammo can damage the gun.
In our standard 14.5" barrels, we have found the 80° piece to be the best all-around angle to reliably run low-pressure ammo such as Steel Challenge hand loads or the 130 Federal Syntech while also reducing recoil for high-pressure loads.
Competitive shooters looking to optimize for recoil reduction will opt to move down to a lower angle, typically the 70°. The 70° piece will run any standard pressure loads but will be closer to the edge of the operational window with low pressure loads like the 130 or 150 Federal Syntech or similar low-pressure hand loads. When running the 70° lock piece with such loads, we recommend more regular cleanings of your JP-5™. Several of our top shooters are running this lock piece successfully.
Compatibility
JP-5™ lock pieces are compatible with the H&K MP5 platform but not all MP5 clones. Any non-H&K MP5 clone that takes H&K lock pieces will be compatible with JP-5™ lock pieces.
Because of the precise geometry of the locking surfaces, switching to a new lock piece may alter the bolt gap of a given rifle. Because of this, we
What an adjustable gas block is to an AR, the lock piece is to the roller-delayed JP-5™ platform. This easily interchangeable component allows you to tune the recoil impulse of your rifle to suit whatever ammo or configuration you want to run.
Like every part we make, our JP-5™ Lock Pieces are a premium component manufactured from a proprietary steel and finished with a highly lubricious nitride coating for low wear and low friction.
Selecting a Lock Piece For Your JP-5™
Lock pieces for the JP-5™/MP5 pattern operating system are distinguished by the angle of the roller bearing surfaces. Most JP-5™ models will ship with the 80° lock piece. This angle determines how much force is required to open the action. The larger the angle, the easier it is for the action to open. So, systems with higher pressure will take a lower angle of lock piece and vice versa.
If you increase the pressure in your system—e.g., changing to a longer barrel, adding a suppressor, switching to higher pressure ammo—a lower-angled lock piece will function better. If you are decreasing the pressure, a higher-angle lock piece might function better.
In general, if your JP-5™ cycles weakly and unreliably, a higher angle of lock piece is recommended. If the bolt is cycling violently with the SCS bottoming out noticeably in the buffer tube, a lower angle of lock piece will help. Be aware that under-delaying the JP-5™ combined with high-pressure ammo can damage the gun.
In our standard 14.5" barrels, we have found the 80° piece to be the best all-around angle to reliably run low-pressure ammo such as Steel Challenge hand loads or the 130 Federal Syntech while also reducing recoil for high-pressure loads.
Competitive shooters looking to optimize for recoil reduction will opt to move down to a lower angle, typically the 70°. The 70° piece will run any standard pressure loads but will be closer to the edge of the operational window with low pressure loads like the 130 or 150 Federal Syntech or similar low-pressure hand loads. When running the 70° lock piece with such loads, we recommend more regular cleanings of your JP-5™. Several of our top shooters are running this lock piece successfully.
Compatibility
JP-5™ lock pieces are compatible with the H&K MP5 platform but not all MP5 clones. Any non-H&K MP5 clone that takes H&K lock pieces will be compatible with JP-5™ lock pieces.
Because of the precise geometry of the locking surfaces, switching to a new lock piece may alter the bolt gap of a given rifle. Because of this, we recommend validating bolt gap of any rifle after changing out the lock piece. validating bolt gap of any rifle after changing out the lock piece.
Aucun avis n'a été publié pour le moment.
Référence: JP-HPG
Marque: JP Enterprises
Hogue Pistol Grip with JP Logo
Référence: JP-JPSL3
Marque: JP Enterprises
Référence: TT-GBP9-XLS
Marque: Taran Tactical
EXTRA POWER SPRING FOR GLOCK PCC BASE PAD, FOR USE WITH GLOCK 9MM 30, 31, AND 33 ROUND MAGAZINE BODIES. GREAT FOR PCC COMPETITION. The extra power spring is designed to enhance feeding and to ensure the bolt locks back when empty. *For use with our Glock PCC +5, PCC +10, and Ultralight PCC +10 magazine extensions.* WARNING: This product can expose you to...
Référence: JP-JPBT-CA
Enhanced Carbine Buffer Tube This JP-SPEC revision of the standard Mil-spec buffer tube improves on the original in both design and finish. We've included an addition stock position (for a total of seven) and given a finer surface finish for smoother function. This design is also designed to allow extra threading into the receiver, which optimizes...
Référence: JP-RPBT-R
COMPATIBLE: AR-15 - les parties communes, 223
Référence: JP-JPTR-FS
Marque: JP Enterprises
Référence: JP-JPSH-1D
Marque: JP Enterprises
Low Mass High Speed Hammer for Small Pin (.154) Receivers
Référence: JP-JPSCHA-LP
Marque: JP Enterprises
Référence: JPSCS2-SM-2
Steel Weight for Silent Captured Spring/VMOS™ Carrier Designed to replace one or more of the existing weights of the JP Silent Captured Spring or VMOS™ Bolt Carrier, these steel weights are the standard components used for reciprocating mass in the operating system.
Référence: JP-JPSL2-Red
Marque: JP Enterprises
Référence: JPTRE3-236TI
Marque: JP Enterprises
Référence: JP-JPSCS-SPA
Marque: JP Enterprises
Référence: JP-JPFCP-1EZ
Marque: JP Enterprises
The new JP EZ Trigger™ represents the best performance value and strikes the best compromise between safety, performance, value and mission-specific versatility. Once you try it, we hope you will agree.
Référence: JP-JPSCS2-HM-2
Tungsten Weight for Silent Captured Spring/VMOS™ Carrier Designed to replace one or more of the existing weights of the JP Silent Captured Spring or VMOS™ Bolt Carrier, these tungsten weights are the standard components used for reciprocating mass in the operating system.
Référence: JP-JPTRE3-236S
Marque: JP Enterprises
Référence: JPSCS2-ORING-PK
Marque: JP Enterprises
Référence: JP-JPAW-1
Marque: JP Enterprises
Torx Head
Référence: JPFCP-1R-BLK
Marque: JP Enterprises
Référence: JP-JPFC-SAD
Marque: JP Enterprises
Référence: JP-JPROS
Marque: JP Enterprises
A true quick detachable 45° rail offset adapter for any Picatinny accessory. This can be used on typical quad-rail hand guards to yield a 45° on bore axis position (1:30 or 10:30 position). For example, the JPoint or JP Short Range Tactical Sight (JPSRTS) can be mounted on two JPROS at 1:30 for a right-handed operator.
Référence: JP-JPSL1-Blue
Marque: JP Enterprises
